Dental materials
Choose a material by matching its properties, substrate, geometry and handling to the clinical task. A restoration succeeds as a tooth–interface–material system, so a strong material cannot compensate for an unsuitable design or a contaminated bond.
Quick revision summary
Mechanical properties: use the right word
Stress is force per area and strain is relative deformation. Elastic modulus describes stiffness within elastic behaviour; strength describes the stress tolerated before a stated failure. Toughness concerns energy absorbed before fracture, and fracture toughness concerns resistance to propagation of a crack.
Glass ionomers, modified materials and luting cements
Conventional glass ionomer sets through an acid–base reaction between a fluoroaluminosilicate glass and an aqueous polyacid. It interacts chemically with tooth tissue and releases fluoride, but early water gain or loss can damage the setting surface.
Read failure before choosing repair or replacement
Identify whether failure occurred in tooth tissue, the adhesive or cement interface, the bulk restorative material or a framework. Look for secondary caries, inadequate thickness, unsupported cusps, contamination, wear, fatigue and loading.
Common mistake
Hardness is not toughness, and zirconia is not an etchable glass ceramic. Product-specific instructions determine safe surface treatment, curing and compatible cementation.
Dental materials
Choose a material by matching its properties, substrate, geometry and handling to the clinical task. A restoration succeeds as a tooth–interface–material system, so a strong material cannot compensate for an unsuitable design or a contaminated bond.
Mechanical properties: use the right word
Stress is force per area and strain is relative deformation. Elastic modulus describes stiffness within elastic behaviour; strength describes the stress tolerated before a stated failure. Toughness concerns energy absorbed before fracture, and fracture toughness concerns resistance to propagation of a crack. Hardness concerns resistance to local indentation or scratching. These are related but not interchangeable properties.
Brittle ceramics can tolerate substantial compression yet fracture from tensile stress at a flaw. Metals generally permit more plastic deformation before fracture. Fatigue is failure under repeated loading below a one-off strength value. Material thickness, support, connector shape, surface damage and occlusal loading therefore matter alongside laboratory strength numbers.
Adhesion and the tooth substrate
Bonding depends on surface preparation, wetting, penetration and polymerisation of a compatible system. Acid-etched enamel permits micromechanical retention. Dentine is a hydrated collagen–mineral substrate with tubules and a smear layer after preparation, making its bonding challenge different from enamel. Deeper dentine is more permeable and can be harder to manage predictably.
Adhesive systems use different etch-and-rinse, self-etch or selective-enamel approaches. Follow the specific system’s instructions for preparation, active application, evaporation and curing. Overdrying, residual solvent, pooling or contamination can compromise the interface. A universal adhesive name does not mean every substrate and luting combination has the same protocol.
Resin composite: components, curing and shrinkage
Composite combines a polymerisable resin matrix, inorganic filler and a coupling system, usually silane, linking filler to resin. Filler affects handling, stiffness, wear and shrinkage, while the matrix and initiator system influence polymerisation. Flowable and more highly filled materials can therefore behave differently even when both are called composite.
Polymerisation contracts the resin phase and can generate stress at bonded interfaces. Placement geometry and curing affect the result; a bulk-fill designation is product-specific rather than permission to cure any depth. Cure depends on wavelength compatibility, irradiance at the restoration, exposure time, distance, angle, shade and access. Maintain and check the curing unit and protect eyes appropriately.
Glass ionomers, modified materials and luting cements
Conventional glass ionomer sets through an acid–base reaction between a fluoroaluminosilicate glass and an aqueous polyacid. It interacts chemically with tooth tissue and releases fluoride, but early water gain or loss can damage the setting surface. Protect it as specified and select an indication compatible with its mechanical properties.
Resin-modified glass ionomer adds resin polymerisation to the acid–base process and is not identical to either conventional GIC or composite. Compomers are resin-based polyacid-modified materials with different setting behaviour again. Luting materials include conventional water-based and resin cements; selection depends on retention form, restorative material, tooth substrate and whether adhesive bonding is required.
| Material family | Useful property | Handling or design limitation |
|---|---|---|
| Resin composite | Adhesion, aesthetics and conservative preparation | Isolation and adequate polymerisation are essential |
| Conventional GIC | Tooth interaction and fluoride release | Early moisture imbalance and high-load fracture concerns |
| Glass-based ceramic | Aesthetic translucency and potential adhesive bonding | Brittle; requires the correct surface treatment and support |
| Zirconia | High-strength polycrystalline ceramic options | Different surface chemistry from silica-based glass ceramics |
| Metal alloy | Useful ductility, strength and thin-section performance | Alloy-specific design, aesthetics and sensitivity considerations |
Indirect ceramics, metals and interface compatibility
Feldspathic porcelain, lithium disilicate and zirconia are not one interchangeable material. Glass-based ceramics contain an etchable glass phase; zirconia is polycrystalline and needs a different bonding strategy. Do not apply a hydrofluoric-acid glass-ceramic protocol to zirconia or improvise intraoral use. The manufacturer’s material-specific treatment and safety instructions determine the actual procedure.
Metal alloys differ in stiffness, ductility, corrosion behaviour and constituent elements. Metal–ceramic systems require compatible thermal behaviour and interface preparation. A veneering ceramic chip is different from a framework fracture, and the repair options differ accordingly. The required restorative space and achievable support should be established before choosing the material.
Impressions, models and denture-base materials
An impression must capture detail and recover sufficiently after removal without unacceptable distortion. Alginate is an irreversible hydrocolloid, while elastomeric materials include addition silicone and polyether with different moisture, stiffness and handling characteristics. Tray support, adhesive, working time, removal and storage matter as much as the family name. Disinfection must be compatible with the material and local processing requirements.
Gypsum products form a model by a setting reaction affected by water–powder ratio, mixing and handling. Denture-base acrylic is commonly PMMA; processing, residual monomer, porosity and thickness influence comfort and strength. A digital scan removes some impression-material issues but still depends on visibility, moisture control, geometry capture and a suitable manufacturing workflow.
Read failure before choosing repair or replacement
Identify whether failure occurred in tooth tissue, the adhesive or cement interface, the bulk restorative material or a framework. Look for secondary caries, inadequate thickness, unsupported cusps, contamination, wear, fatigue and loading. Replacing a restoration without correcting its failure mechanism can enlarge the defect while repeating the problem.
Refurbishment reshapes or polishes a serviceable restoration; repair adds material to correct a local defect; replacement removes the existing restoration. Consider the extent of the problem, remaining structure, pulp risk, patient priorities and ability to achieve a durable interface. Material selection should include a realistic maintenance and repair pathway, with current restrictions and product instructions checked for the intended use.
A distinction to remember
Hardness is not toughness, and zirconia is not an etchable glass ceramic. Product-specific instructions determine safe surface treatment, curing and compatible cementation.
A posterior restoration fractures twice at the same thin cusp, while its bonded material largely remains intact. Is a stronger filling material the main solution?
Reveal the reasoning
The recurring tooth fracture suggests a structural or loading problem. Assess remaining cusp support, material and tooth thickness, occlusion, parafunction and cracks. A different material alone may leave the same stress concentration; the design and need for cusp protection require reassessment.
Test your recall
How does stiffness differ from strength?
Show answer
Stiffness is resistance to elastic deformation, described by elastic modulus. Strength is the stress tolerated before a specified failure. A material can be stiff yet brittle, so neither property alone establishes resistance to cracking or suitability for a restoration.
